DHT22 เซนเซอร์วัด อุณหภูมิ+ความชื้น อย่างดี มีความละเอียดและความแม่นยำสูง
ตามสเปกระบุไว้ว่า
รายละเอียด DHT22
Accuracy humidity +-2%RH(Max +-5%RH); temperature +-0.2Celsius
Resolution or sensitivity humidity 0.1%RH; temperature 0.1Celsius
Repeatability humidity +-1%RH; temperature +-0.2Celsius
Humidity hysteresis +-0.3%RH
Long-term Stability +-0.5%RH/year
Sensing period Average: 2s
Interchangeability fully interchangeable
Features DHT22:
3.3-6V Input
1-1.5mA measuring current
40-50 uA standby current
Humidity from 0-100% RH
-40 - 80 degrees C temperature range
+-2% RH accuracy
+-0.5 degrees C
รายละเอียด PIN OUT
ขา 1 เป็น VCC ต่อ 3.3 - 6V
ขา 2 เป็นขา Data ต่อเข้า MCU
ขา 3 ไม่ใช้งาน
ขา 4 ต่อ GND
ตามรูปด้านล่าง
รายละเอียด Timing
การใช้งานต่อ
รายละเอียดโปรแกรม
// Example testing sketch for various DHT humidity/temperature sensors
// Written by ladyada, public domain
include "DHT.h"
define DHTPIN 2 // what pin we're connected to
// Uncomment whatever type you're using!
//
define DHTTYPE DHT11 // DHT 11
define DHTTYPE DHT22 // DHT 22 (AM2302)
//
define DHTTYPE DHT21 // DHT 21 (AM2301)
// Connect pin 1 (on the left) of the sensor to +5V
// NOTE: If using a board with 3.3V logic like an Arduino Due connect pin 1
// to 3.3V instead of 5V!
// Connect pin 2 of the sensor to whatever your DHTPIN is
// Connect pin 4 (on the right) of the sensor to GROUND
// Connect a 10K resistor from pin 2 (data) to pin 1 (power) of the sensor
// Initialize DHT sensor for normal 16mhz Arduino
DHT dht(DHTPIN, DHTTYPE);
// NOTE: For working with a faster chip, like an Arduino Due or Teensy, you
// might need to increase the threshold for cycle counts considered a 1 or 0.
// You can do this by passing a 3rd parameter for this threshold. It's a bit
// of fiddling to find the right value, but in general the faster the CPU the
// higher the value. The default for a 16mhz AVR is a value of 6. For an
// Arduino Due that runs at 84mhz a value of 30 works.
// Example to initialize DHT sensor for Arduino Due:
//DHT dht(DHTPIN, DHTTYPE, 30);
void setup() {
Serial.begin(9600);
Serial.println("DHTxx test!");
dht.begin();
}
void loop() {
// Wait a few seconds between measurements.
delay(2000);
// Reading temperature or humidity takes about 250 milliseconds!
// Sensor readings may also be up to 2 seconds 'old' (its a very slow sensor)
float h = dht.readHumidity();
// Read temperature as Celsius
float t = dht.readTemperature();
// Read temperature as Fahrenheit
float f = dht.readTemperature(true);
// Check if any reads failed and exit early (to try again).
if (isnan(h) || isnan(t) || isnan(f)) {
Serial.println("Failed to read from DHT sensor!");
return;
}
// Compute heat index
// Must send in temp in Fahrenheit!
float hi = dht.computeHeatIndex(f, h);
Serial.print("Humidity: ");
Serial.print(h);
Serial.print(" %\t");
Serial.print("Temperature: ");
Serial.print(t);
Serial.print(" *C ");
Serial.print(f);
Serial.print(" *F\t");
Serial.print("Heat index: ");
Serial.print(hi);
Serial.println(" *F");
}
ผลการทดสอบ
สนใจสั่งซื้อกับทางร้าน
\>>> คลิก
DHT22 โมดูลเซนเซอร์วัดความชื้นและอุณหภูมิในตัวเดียว มีความแม่นยำสูง มีตัวต้านทาน Pull up มาแล้วสามารถต่อขาทดลองได้เลยไม่ต้องต่อเพิ่ม
ถ้าต้องการความถูกต้องแม่นยำในการวัดอุณหภูมิและความชื้น แนะนำตัวนี้เลย DHT22 High Accuracy Digital Temperature and Humidity Sensor DHT22 ใช้สำหรับวัดอุณหภูมิและความชื้น ออกแบบมาให้วัดได้แม่นยำกว่ารุ่น DHT11 ใช้ง่ายสามารถนำ DHT22 ไปเปลี่ยนแทน DHT11 ได้เลยเพราะโค้ด Arduino DHT22 เขียนเหมือนกัน